NIPPON PAPER SUPERCHLON®CP622

产品详情

产品参数

1. Introduction:

Superchlon CP622 is based on chlorinated polypropylene resin and is used as a primer for polypropylene materials. Polypropylene plastic has low weight, low cost, and excellent physical properties, chemical resistance, and heat resistance, making it widely used. However, its crystal structure and non-polar surface make adhesion difficult, limiting its application. Superchlon CP622 can solve this problem because it has excellent adhesion to polypropylene plastics and surface coatings made of polyurethane, acrylic, amino, epoxy, or alkyd resins. Superchlon CP622 is commonly used as an adhesion promoter in polyolefin automotive bumper coatings. In addition, Superchlon CP622 can also establish structural adhesion between polypropylene and other materials such as aluminum foil, fiber paper, polyester, and other plastics.

2. Specification: 20kg/box

Appearance: light yellow small pieces

Color (Gardner) 6 or below

Viscosity (25 ℃, Pas) 20-80 (20% solid content dissolved in toluene/isopropanol: 97/3)

Chlorine content 24.5 ± 1.0%

Molecular weight 40000-70000

Softening point 70-80 ℃

3. Solubility:

溶剂	溶解度	溶液外观
二甲苯	完全溶解	清澈
甲苯	完全溶解	清澈
环己烷	溶解	接近清澈
乙基环己烷	溶解	接近清澈
甲基环己烷	溶解	接近清澈
异丙醇	不溶解	沉淀

4. Compatibility:

Superchlon CP622 mixed with other resins can enhance the adhesion between the primer and topcoat. Compared with traditional low chlorinated polyolefin resins, Superchlon CP622 has been improved to enhance its adhesion to other resins. The following is the compatibility data of Superchlon CP622 and other resins. Please note that if the proportion of other resins mixed is too high, it will reduce the adhesion to the polypropylene substrate. It is recommended that the proportion of other resins mixed should not exceed 30% by weight.

l 与其它树脂兼容性

其它树脂	兼容性		树脂类型	生产商
	20% 甲苯溶液	漆膜
Paraloid A-11	○	○	热塑性丙烯酸	Rohm & Hass
Paraloid B-44	△	△	热塑性丙烯酸	Rohm & Hass
Paraloid B-66	x	x	热塑性丙烯酸	Rohm & Hass
Paraloid B-72	x	x	热塑性丙烯酸	Rohm & Hass
Dianal BR-102	x	x	热塑性丙烯酸	Mitsubushi Rayon
Cotax GX-059	○	○	热塑性丙烯酸	Toray Fine Chem
Laroflex MP-35	◎	◎	聚氯乙烯	BASF
Laroflex MP-45	◎	◎	聚氯乙烯	BASF
Evaflex-40	○	○	乙烯醋酸酯	Mitsui Polychem
Phthalkyd 355-50	◎	○	醇酸	Hitachi Chem
Phthalkyd 375	◎	◎	醇酸	Hitachi Chem
Phthalkyd V-902	◎	○	丙烯酸改性醇酸	Hitachi Chem
Phthalkyd V-903	△	○	丙烯酸改性醇酸	Hitachi Chem
Nisseki neopolymer 120	◎	○	石油树脂	Nihon Petrochem
Nisseki neopolymer 140	◎	○	石油树脂	Nihon Petrochem
Beckacite 1120	○	○	马林树脂	Nihon Reichoid
Pencell KK	◎	○	松香	Arakawa Chem
Tamanol 350	△	△	酚醛	Arakawa Chem
Lignol R-140	◎	○	二甲苯树脂	Lignite
Nikanol HP-70	◎	△	二甲苯树脂	Mitsubushi Gaschem

NOTE ◎---- 相容 ○---- 大部份相容 △---- 部份相容 x ---- 不相容

5. SUPERCHLON CP622's heat sealing strength for various membranes:

Superchlon CP622 is coated onto pre treated polypropylene film, left at room temperature for 10-15 minutes, heat sealed with various films, and tested for peel strength.

Experimental conditions:

-Heat sealing conditions: 100 ℃, 1kg/cm2, 1 sec

-Peel test: 15mm , 180 °, 50mm/minute

-Coating amount: 3g/㎡ (dry)

Experimental results: